Michi Seibi
11 September 2016 10:4911.09.2016 10:49
Hello,
I'm experiencing slight vibrations at the rear of my car. I've already tried different tail fins. I've installed the torque tube correctly and also tried installing it the other way around.
I've noticed that I can easily pull my tailpipe in and out. Why is there play there?
Michi
Hallo,
ich habe leichte Vibrationen an meinem Heck. Habe schon verschiedene Heckblätter probiert. Die Torque Tube habe ich richtig montiert und auch schon mal anders rum eingebaut.
Ich habe bemerkt dass ich meine Heckwelle leicht rein und raus ziehen kann. Wieso habe ich dort spiel?
Michi
Michi Seibi
11 September 2016 11:1911.09.2016 11:19
Addendum:
I don't have a Pro version on the Neo, so I can't do a vibration analysis. But the log shows strong and dangerous vibrations while hovering.
Nachtrag:
Ich hab kein Pro auf dem Neo, kann somit keine Vibrationsanalyse machen. Aber im Log zeigt es mir beim schweben schon starke und gefrliche Vibrationen an.
Eddi E. aus G.
12 September 2016 11:2412.09.2016 11:24
Hi,
ohne Pro kannst Du nur mit der kleinen Anzeige hier versuchen, der Sache auf die Spur zu kommen, und mit Anfassen (man spürt eigentlich am Chassis/Heckrohr ganz gut Unterschiede). Vorsicht, natürlich ohne Hauptrotorblätter und wenn mit Heckrotorblättern bitte am Servo so aushängen, dass das Servo das Heck nicht ansteuern kann.
Was sind 'leichte Vibrationen', wie kann ich mir das vorstellen?
Wie weit kannst Du die Heckwelle axial bewegen? Ein Minimales Spiel ist normal, OK, und auch über hunderte wettbewerbsmäßige Flüge bei unseren Teamies kein Problem, tatsächlich hat noch keiner am Heck etwas nacharbeiten müssen soweit ich weiß. Wenn's 2,7 mm sind, hast Du was vergessen ;-)
Starrantrieb ... wenn die Welle auch nur den Hauch eines Schlages hat ... das ließe sich aber identifizieren, indem man zunächst nur die Mechanik, dann Mechanik mit Heckrohr, dann Mechanik mit Heckrotor laufen lässt und eben die Anzeige vergleicht.
Grüßle
Eddi
Born to fly ...
forced to work.
Michi Seibi
12 September 2016 14:5012.09.2016 14:50
Thanks for the info. I got the Pro version yesterday and got these results:
Without all 4 rotor blades, the helicopter was standing in the grass:
Approx. 1400 RPM: 400
1800 and 2100 RPM: 200
I consider that to be low-vibration and perfectly fine.
During flight, while hovering, I recorded these values:
1400 RPM: 3300 (full deflection in the VBar Control)
1800 RPM: 2500
2100 RPM: 1500
The vibrations can be felt at the skids, rear struts, and rear linkage. A slight droning sound can also be heard.
- I tested two different sets of RT 710 and RT 105 and had the same problem with both.
- For testing purposes, I also reversed the torque tube (the 60mm distance is now at the rear). I didn't notice any difference compared to before.
- There was already about 0.4-0.5mm of play in the rear. I eliminated that with shims.
- I am certain that all axial bearings are installed correctly.
What could be the cause? My guess would be unbalanced leaves. However, with only two sets of leaves, that's rather unlikely. I can test that this evening.
Is the mechanism with the values at the very top also low-vibration without leaves, or should it be even better?
Michi
Danke für die Infos. Ich habe mir gestern noch die Pro Version geholt und habe diese Ergebnisse:
Ohne allen 4 Rotorblättern und der Heli stand im Gras:
ca. 1400 RPM: 400
1800 und 2100 RPM: 200
Das sehe ich als vibrationsarm und voll in Ordnung.
Im Flug habe ich im schweben diese Werte:
1400 RPM:3300 (Vollausschlag in der V Bar Control)
1800 RPM:2500
2100 RPM:1500
Man erkennt die Vibrationen an den Kufen, Heckstreben und Heckanlenkung. Ebenfalls hört man ein leichtes dröhnen.
- Ich habe zwei verschiedene Sätze RT 710 und RT 105 getestet und bei beiden das selbe Problem.
- Zum Test habe ich auch noch die Torque Tube umgedreht (60mm Abstand ist jetzt hintem am Heck). Da habe ich zu vorher keinen Unterschied bemerkt.
- Spiel im Heck war schon so 0,4-0,5mm. Das habe ich mit Scheiben beseitigt.
- Bei allen Axiallagern bin ich mir sicher dass sie richtig rum eingebaut sind
Woran könnte es jetzt liegen? Blätter unwuchtig wäre mein Tipp. Jedoch bei 2 Blattsätzen eher unwarscheinlich. Das kann ich heute Abend mal noch testen.
Ist die Mechanik mit den Werten ganz oben ohne Blättern auch vibrationsarm oder sollte das noch besser sein?
Michi
Eddi E. aus G.
12 September 2016 15:1512.09.2016 15:15
Hi,
spannend wäre mal mit Heckblättern, auf dem Boden. ich denke, das sind hochfrequente Vibrationen, die durch die Blätter verstärkt werden.
Bei 1.400 ist eventuell eine Resonanz, wo das besonders zum Tragen kommt.
Läuft die Heckwelle rund (Nabe runter, Fingernagel-Probe ...)?
Der Heckrotor an sich ist ja der vom 700 XX, und der ist so ziemlich über jeden Verdacht erhaben.
Heckblätter, da habe ich mal bei einem anderen Hersteller so meine Erfahrungen gemacht. Am Ende hat ein Blatt aus Satz 1 mit einem anderen aus Satz 2 zusammen gepasst :-)
Referenzwerte geben mir unsere Team-Piloten, ich poste sobald ich sie habe, oder die direkt.
Grüßle
Eddi
Born to fly ...
forced to work.
Michi Seibi
12 September 2016 15:3512.09.2016 15:35
Just did test runs on the ground using only rear blades.
I have two sets of RT 105s that I previously used on my Forza. These two sets are causing the vibrations on the L700.
At a standstill of approximately 1400 RPM, the vibration analysis showed 1600.
Then I unpacked a new set of tail blades from the kit and ta-da! Only 150 vibrations instead of 1600.
Incidentally, during the strong vibrations, it was clearly visible that the rear hub moved back and forth by about 10mm.
I hope I didn't damage anything back there during those few minutes of test flight....
Michi
Gerade Probeläufe auf dem Boden nur mit Heckblättern gemacht.
Ich habe 2 Sätze RT 105, die ich vorher auf meinem Forza geflogen bin. Die beiden Sätze verursachen am L700 die Vibrationen.
Im Stand bei ca. 1400 RPM hat die Vibrationsanalyse 1600 angezeigt.
Dann habe ich ein neues Heckblätter Set aus dem Kit ausgepackt und taddaaaa. Nur noch 150 statt 1600 Vibrationen.
Übrigens: Bei den starken Vibrationen hat man deutlich gesehen, dass die Hecknabe so gut 10mm hin und her geht bei den Vibs.
Ich hoffe ich hab mir in den wenigen Testflugminuten nichts kaputt gemacht dort hinten....
Michi
Eddi E. aus G.
12 September 2016 17:0912.09.2016 17:09
Hi,
und ... oha. Naja, wenn alles mechanisch OK ist, sollte da kein bleibender Schaden sein. Einfach mal ein bisschen im Auge behalten.
Grüßle
Eddi
Born to fly ...
forced to work.
Michi Seibi
12 September 2016 19:2212.09.2016 19:22
I'll do that. Which way should I install the torque tube? The way it's shown in the manual, or the other way around? Or does it not matter? The designer must have had a reason for those spacings...
Werde ich machen. Wie rum soll ich jetzt die torque tube einbauen? So wie im manual oder genau andersrum? Oder ist es egal? Der liebe konstruktör wird sich bei den abständen schon was gedacht haben...
Eddi E. aus G.
13 September 2016 08:3313.09.2016 08:33
Hi,
grundsätzlich wäre es egal, wenn/solange die Lagerungen nicht in gleichmäßigen Abständen montiert werden. Das könnte zu einem Aufschwingen/zu Resonanzen führen.
Wenn Du es nach Anleitung machst, bist Du auf jeden Fall auf der sicheren Seiten.
Grüßle
Eddi
Born to fly ...
forced to work.