Jurij-Heli
5 October 2016 15:1305.10.2016 15:13
Hello,
I have a question. I'd like to try out the VGov controller and I have a Kosmik ESC where I can disable the RPM control via a program disc, and a VBar Neo. I have a Mikado governor cable at home that's designed for the YGE 160HV. If I connect the master to the ESC and the slave to the RPM using the governor cable, will that work? Like I said, I'm unsure because this cable is for YGE, but basically all ESCs are the same; they all have a master and slave.
Greeting
Jurij
Hallo,
Ich habe da mal eine Frage. Ich möchte mal den VGov probieren habe dazu einen Kosmik bei dem ich via Progdisc die Drehzahlregelung ausschalten kann und eine Vstabi Neo. Jetzt habe ich zuhause einen Mikado Governor Kabel was für den YGE 160HV bestimmt ist. Wenn ich Master an ESC stecke und Slave mit dem Governorkabel an RPM wird das so funktionieren? Wie gesagt bin ich unsicher da dieses Kabel für YGE bestimmt ist aber im Grunde ist jeder Regler gleich, alle haben ein Master und Slave.
Gruss
Jurij
HeliALEX
5 October 2016 15:3805.10.2016 15:38
Hello Jurij,
The VBar Governor cannot be used with the Kosmik.
Scorpion or YGE controllers, for example, work with VBar Governor.
Best regards
Alex
Hallo Jurij,
der VStabi Govenor kann mit dem Kosmik nicht benutzt werden.
Für VStabi Govenor funktionieren z.B. Scorpion oder YGE Regler.
Viele Grüße
Alex
Jurij-Heli
5 October 2016 15:5505.10.2016 15:55
Hello,
Yes, if it works with all Jives, it should also work with the Kosmik. I can adjust the speed control from the Kosmik. It's important for me to know if the governor cable fits, as this cable is sold for the YGE 160 and I want to use it on the Kosmik. Should that work?
Hallo,
Ja wenn es mit allen Jives geht geht es auch mit dem Kosmik. Ich kann die Drehzahlregelung vom Kosmik aus stellen. Für mich wäre wichtig ob das Governorkabel passt da dieses Kabel für YGE 160 verkauft wird und ich ihn auf dem Kosmik verwenden möchte, sollte gehen?
HeliALEX
5 October 2016 16:4205.10.2016 16:42
Hello Jurij,
It's not a yes or no. It doesn't work!
Even in controller mode, the Kosmik does not pass the speed input signals 1:1 to the motor; if a controller does not do this, the control behavior will be very poor.
Regards, Alex
Hallo Jurij,
nicht ja, nein. Es funktioniert nicht!
Auch im Steller Mode gibt der Kosmik die Drehzahl- Eingangssignale nicht 1:1 an den Motor weiter, tut dies ein Regler nicht bekommt man ein sehr schlechtes Regelverhalten.
Gruß Alex
Jurij-Heli
5 October 2016 17:3405.10.2016 17:34
Hi Alex,
Okay, so be it! I experimented and came to the same conclusion as you: it doesn't work. Now for a silly question: How does the YGE 90LV handle it? Was the signal cable from the BEC also removed and connected to the RPM output? Do you put it into a special "mode" so it communicates with VGov via slave, or how does that work? Sorry for the dumb questions :-(
Edited once. Last edited on 05/10/2016 at 17:35 by Jurij-Heli.
Hallo Alex,
gut dann soll es so sein! Ich habe herumprobiert und bin zum gleichen Entschluss gekommen wie du das geht nicht. Dann mal eine Dumme Frage: Wie macht es der YGE 90LV? Dem wurde auch das Signalkabel des BEC´s entzogen und an den RPM Ausgang angschlossen? Versetzt mann sie in einen speziellen "Modus" damit er mit VGov kommuniziert über Slave oder wie läuft das. Sorry für die dummen Fragen :-(
1 mal bearbeitet. Zuletzt am 05.10.2016 17:35 von Jurij-Heli.
HeliALEX
5 October 2016 17:5305.10.2016 17:53
Jurij-Heli wrote:
-------------------------------------------------------
Hi Alex,
>
Okay, then so be it! I've been experimenting.
> and I came to the same conclusion as you
That's not possible. Then a silly question: How
Does the YGE 90LV do it? That one was also given the...
> Signal cable of the BEC disconnected and connected to the RPM
> Exit connected? Are they placed in a
> special "mode" so that it communicates with VGov
> Via slave, or how does that work? Sorry for the
> stupid questions :-(
Hello Jurij,
Yes, I don't just write that for no reason.
A YGE controller has the speed signal at its slave output (orange cable), which the VBar can process. Kontronik controllers cannot. And as already mentioned: Even in controller mode, the Kosmik doesn't pass the speed input signals directly to the motor; if a controller doesn't do this, you get very poor control performance.
Controllers don't "communicate" via the slave; nothing is transmitted via the signal line on the slave cable. Therefore, it was used to carry the RPM signal (YGE). Other manufacturers use a separate cable for this (Scorpion). I have a very old YGE controller here where the slave signal cable still doesn't output anything, so it wasn't always like this.
When a Scorpion or YGE is put into controller mode, the signal that is sent from the VBar to the controller also reaches the motor.
Hope this helps you.
Best regards
Alex
Jurij-Heli schrieb:
-------------------------------------------------------
> Hallo Alex,
>
> gut dann soll es so sein! Ich habe herumprobiert
> und bin zum gleichen Entschluss gekommen wie du
> das geht nicht. Dann mal eine Dumme Frage: Wie
> macht es der YGE 90LV? Dem wurde auch das
> Signalkabel des BEC´s entzogen und an den RPM
> Ausgang angschlossen? Versetzt mann sie in einen
> speziellen "Modus" damit er mit VGov kommuniziert
> über Slave oder wie läuft das. Sorry für die
> dummen Fragen :-(
Hallo Jurij,
ja ich schreibe das halt nicht einfach so.
Ein YGE hat am Slave Ausgang das Drehzahl- Signal anliegen (oranges Kabel), welches das VStabi verarbeiten kann. Kontronik nicht. Und wie schon gesagt : Auch im Steller Mode gibt der Kosmik die Drehzahl- Eingangssignale nicht 1:1 an den Motor weiter, tut dies ein Regler nicht bekommt man ein sehr schlechtes Regelverhalten.
Regler "kommunizieren" nicht über Slave, über die Signal Leitung am Slave Kabel wird nichts übertragen, somit hat man das halt genutzt um es mit dem Drehzahl Signal zu belegen (YGE) andere Hersteller haben dafür wieder ein extra Kabel (Scorpion). Ich habe einen ganz alten YGE hier bei dem das Singal Kabel vom Slave noch nichts ausgibt, war also nicht immer so.
Stellt man einen Scorpion oder YGE in den Steller- Betrieb kommt das Signal welches vom VStabi zum Regler gegeben wird auch beim Motor an.
Hoffe das hilft dir.
Viele Grüße
Alex
Jurij-Heli
5 October 2016 22:2705.10.2016 22:27
Hello,
I got the engine speed displayed on the screen thanks to the speed sensor, so that issue is resolved, thank you very much!
Greeting
Jurij
Hallo,
Ich habe mir die Drehzahl auf den Bildschirm geholt dank Drehzahlsensor, daher ist das Thema auch erledigt, vielen Dank!
Gruss
Jurij