← Logo 700 and 800

Tail boom wobbles

Mikado Model Helicopters › Logo 700 and 800 · Started by Marianovbar on 14 December 2020 22:0814.12.2020 22:08
Marianovbar 14 December 2020 22:0814.12.2020 22:08
Hi, i have a logo 700 with Vbar neo. Doing climbouts with pirouette, when i stop, the boom wobbles. I have vtx697 and hard dumpers (boths of the outside one of each side). I don't if i have to change my gain for more or less, i already did one optimizing flight but nothing changes.
Regards.
Eddi E. aus G. 15 December 2020 09:0415.12.2020 09:04
Hello,

for my inner cinema: you climb with full collective, piro right or left, stop (considerably hard I suppose), then the boom does what? Wobble up/down, wobble (wag) left/right?

At which rpm, and is it different, with different rpm?
At which ambient temperatures?
Was it there from the beginning, or did it just occur lately?
Does it also wobble in a hover, when you briskly trigger aileron or elevator and stop again quickly? Like you induce a wobble, and the system has to flatten it out again?

Usually, an up/down wobble in a stop would be a matter of CoG and trim flight, and a left/right wag a thing of trim flight, given that the mechanical setup is good enough, including blade tracking and balancing.

Changing gains will 'only' affect how hard the VBar _re_acts to deviations, so it can only do so much. If there are little or no deviations (e.g. CoG or trim flight), the whole thing will be much more stable to begin with. If there is an action (deviation/offset) and a reaction (control input), you see it, while if there's none, there's none necessary, you don't see it.

Kind regards

Eddi

Born to fly ...
forced to work.
Marianovbar 15 December 2020 20:0415.12.2020 20:04
Hi Eddie. The boom wobbles up/down while pirouetting climbouts, if it's a hard stop or slow stop does it. In any rpm bank is the same with 1800rpm and 2200rpm. Also, When i do some jabs of aileron or elevator the boom wobble a little bit maybe in that point is the gain but i tell you to know. CG is perfect and a weird thing is that i did the trim flight but the pirouette still oscilating as if pyro compensation does not work and i think there is part of the issue, but i don't know if the trim flight has to be performed without touching the trim servos in the setup or is the same.
Regards.
Eddi E. aus G. 16 December 2020 08:5516.12.2020 08:55
Good morning,

on the swash plate, you hear too much gain before you see it, because of the refined filtering.
On some models, you can max it out (and Style, too), without any wobbling or oscillation.

I'd try the following: check if the NEO requires an update—there was a bug in the last update which could cause the pirouette compensation to be slightly off, depending on the tail servo type (frequency) selected.

Then, eyeball the swash plate center position (or measure it), adjust trims if necessary.

Then, check the center of gravity with battery installed and canopy on, by holding the model knife edge and checking if the nose or tail drops (both directions, nose left, nose right), adjust by moving the battery if necessary.

Last, re-do the trim flight.

Of course that's only one thing, could also be the dampening, check that O-Rings are still OK and not worn, and properly lubed.
Also check the tail rotor hub, and balance the tail blades—believe it or not, but I more than once had a tail out of balance causing an intermittent or constant wobble on the main rotor head.

I'd be curious to see your overall setup (please save, zip, attach here), there are some more things which could affect that, like heli size.

Then, there's servos, linkages (imprecision, slop, binding), all not very likely but not unheard of.

But one thing after the other, first I'd try again things where I do not have to disassemble.

Kind regards

Eddi

Born to fly ...
forced to work.



1 mal bearbeitet. Zuletzt am 16.12.2020 08:57 von Eddi E. aus G..
Marianovbar 16 December 2020 20:3416.12.2020 20:34
Hi eddie. I just finished to update my NEOs so i will test this weekend.
I saw the CoG and is perfect. I didn't check the dumpers for long time, i have outer hard dumpers 90 shore but i don't know if hard dumper require higher gain, anyway, i will check them.
Thank you and regards. Dateianhänge:
öffnen | Download - 11001637_vbar_LOGO_700.vbr (2.3 KB)
VStabi VStabi Pioneer of Flybarless