maurice.krause
10 March 2025 18:0810.03.2025 18:08
Hello everyone,
Since switching from a Vstabi NoVlink NEO to an EVO, I've had a problem with the tail. The settings have remained the same; here are my helicopter's specs:
This tail twitching only occurs during certain flight maneuvers.
I also have dangerous vibrations logged, but I haven't been able to determine their cause yet. Perhaps it's because I have the hard damping completely installed on the rotor head?
Logo 700 AZ700 Pro & AZ 105 Pro.
Engine Scorpion HK 4525-520 ULTIMATE
Hobbywing 200A with 8V BEC
Savöx SB-2290SG 3x swashplate
Savöx SB-2291SG tail servo
Vstabi EVO latest version 7.
Here's an unlisted link to YouTube:
https://youtu.be/NcTkDqAuAG8 Rear settings in the Vbar Control:
Expo: 28
Yaw Rate: 136
Gain: 77
Proportional: 88
Integral: 60
Coll. Precomp 60, 37, 45
Cycl. Precomp: 7
Optimizer ON
Thank you for your help in advance.
Greetings
Maurice
Hallo zusammen,
ich habe seit der Umstellung von einem Vstabi NoVlink NEO zu einem EVO ein Problem mit dem Heck, Einstellungen sind soweit gleich geblieben, anbei erstmal meine Daten zum Heli:
Dieses Heckzucken ist auch nur bei manchen Flugmanövern.
Ich habe auch Gefährliche Vibrationen im LOG stehen, woher die kommen konnte ich noch nicht feststellen? Vielleicht weil ich am Rotorkopf die harte Dämpfung komplett habe?
Logo 700 AZ700 Pro & AZ 105 Pro.
Motor Scorpion HK 4525-520 ULTIMATE
Hobbywing 200A mit 8V BEC
Savöx SB-2290SG 3x Taumelscheibe
Savöx SB-2291SG Heckservo
Vstabi EVO aktuellste Version 7.
Hier ein nicht gelisteter Link zu Youtube:
https://youtu.be/NcTkDqAuAG8
Heck Einstellungen in der Vbar Control:
Expo: 28
Yaw Rate: 136
Gain: 77
Proportional: 88
Integral: 60
Coll. Precomp 60, 37, 45
Cycl. Precomp: 7
Optimizer ON
Danke für die Hilfe im Voraus
Grüße
Maurice
RV
10 March 2025 18:1210.03.2025 18:12
And when, where, and how am I supposed to see what in the video snippet?
Twitching at the rear in general... were the bearings of the pulleys electrically connected?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 10.03.2025 18:12 von RV.
Und wann und wo und wie soll ich in dem Video Snippet was sehen?
Zucken am Heck generell ... wurden die Lager der Riemenräder elektrisch leitend verbunden?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 10.03.2025 18:12 von RV.
maurice.krause
10 March 2025 18:2110.03.2025 18:21
RV wrote:
-------------------------------------------------------
And when, where, and how should I be in the video?
> What snippet should I see?
>
>
> Twitching at the rear end in general... were the bearings checked?
> Are the pulleys electrically connected?
Hi Rainer, in the video, I know you might not see it very well, it's only 3 seconds long, but you can hear it.
I don't quite follow your question about electrically conductive connections; if you mean the anti-static set, yes, I have installed that.
Greetings Maurice
RV schrieb:
-------------------------------------------------------
> Und wann und wo und wie soll ich in dem Video
> Snippet was sehen?
>
>
> Zucken am Heck generell ... wurden die Lager der
> Riemenräder elektrisch leitend verbunden?
Hallo Rainer, im Video, ich weiß man sieht es vielleicht nicht so gut, ist ja auch nur 3 sek lang, aber man hört es.
Ich kann dir mit der Frage zu elektrisch leitend verbunden nicht ganz folgen, falls du das anti static set meinst, ja das habe ich verbaut.
Grüße Maurice
Eddi E. aus G.
11 March 2025 09:1511.03.2025 09:15
Good morning,
Difficult to answer, 'it could be anything' :-)
. Antistatic (installed, OK)
Servo
Cable/plug
Motor/controller (cable/insulation/short circuit to ground; a twitching can also be seen at the rear)
other electrical effects (peaks)
I tried to find logs, but... nothing in the cloud.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
schwer zu beantworten, 'kann alles sein' :-)
. Antistatik (verbaut, OK)
. Servo
. Kabel/Stecker
. Motor/Regler (Kabel/Isolierung/Masseschluss, ein Zucken da sieht man auch am Heck)
. andere elektrische Effekte (Spitzen)
Ich habe versucht, Logs zu finden, aber ... nix in der Cloud.
Grüßle
Eddi
Born to fly ...
forced to work.
florian_neuner
11 March 2025 10:5011.03.2025 10:50
Hello Maurice,
With what frequency (Hz) are you controlling the tail servo?
If this is a silly question, have you ever tried simply turning down the gain on the rear gain?
Are you flying Vgov or the external Hobbywing Gov?
The Coll. Precomp seems quite high to me, how did you set it?
LG Flo
Edited once. Last edited on 11.03.2025 at 10:51 by florian_neuner.
Hallo Maurice,
mit wie viel Herz steuerst du denn das Heckservo an?
Hast du blöd gefragt schonmal versucht einfach das Heck Gain runter zu drehen?
Fliegst du Vgov oder den Externen Hobbywing Gov?
Die Coll. Precomp kommt mir auch ziemlich hoch vor, wie hast du diese denn eingestellt?
LG Flo
1 mal bearbeitet. Zuletzt am 11.03.2025 10:51 von florian_neuner.
maurice.krause
11 March 2025 17:5111.03.2025 17:51
Hello everyone,
Thanks for the replies so far. To answer @Eddi's question, how could I manually upload the data to the cloud?
@Florian I'm controlling the servos with 1520µs / 333Hz, I've already turned the gain down to 70, which got rid of the twitching, but then the servo wasn't reacting quickly enough.
I'm flying with Vgov.
I'm flying Mirko Cesena's setup, which I really liked with the Vstabi NEO, and well, the helicopter itself flies really great, I can't really complain, except for the tail twitching.
Thank you very much in advance for your help.
Greetings
Maurice
hallo zusammen,
danke erstmal für die Antworten, um auf die Antwort von @Eddi zu antworten, wie könnte ich denn die Daten in der Cloud vielleicht manuell hochladen?
@Florian ich steuere die Servos mit 1520µs / 333Hz an, gain hab ich schon auf 70 runtergedreht, da war das zucken weg, aber dann hat das Servo nicht mehr schnell genug gegengesteuert.
Ich fliege mit dem Vgov.
Ich fliege das Setup von Mirko Cesena, das hat mir mit dem Vstabi NEO sehr gut gefallen und naja an sich fliegt der Heli auch echt super ich kann mich eigentlich nicht beschweren, bis auf das Heckzucken.
Ich danke euch im Voraus sehr für die Hilfe.
Grüße
Maurice
florian_neuner
11 March 2025 18:3511.03.2025 18:35
333Hz is the maximum for the Savöx servo, right?
What sensitivity setting do you have for vgov?
Unfortunately, you can't directly transfer the setup or values from a Neo to an EVO. It's possible, but since the EVO has much faster hardware, this results in different values, especially regarding sensitivities.
What exactly do you mean by the servo reacting too slowly?
333hz ist für das Savöx servo das Maximum oder?
Welche Empfindlichkeit hast du denn beim vgov?
Du kannst aber leider nicht das Setup bzw. die Werte von einem Neo auf ein EVO direkt übernehmen, also geht schon aber da das EVO ja viel schnellere Hardware hat ergeben sich daraus auch andere Werte, speziell bei Empfindlichkeiten.
Wie genau meinst du denn dass dir das Servo zu langsam gegengesteuert hat?
maurice.krause
11 March 2025 18:4611.03.2025 18:46
Hi Florian,
I'm flying the Vgov with a sensitivity of 0.
By "counter-steering" I mean how long it takes until it locks into place; it's not an unimaginably long time, but because of this over-rotation, as I'll call it, the helicopter feels very uncomfortable.
Greetings
Maurice
Hi Florian,
Ich fliege den Vgov mit 0er Empfindlichkeit.
Mit gegengesteuert meine ich wie lang es dauert bis er einrastet, ist jetzt keine unvorstellbare lange zeit, aber durch dieses nachdrehen nenn ich es mal, fühlt sich der Heli sehr unwohl an.
Grüße
Maurice
florian_neuner
11 March 2025 18:5811.03.2025 18:58
Hi Maurice,
Interesting, may I ask why you're using vgov if you're flying with 0 gain? Then you're essentially flying without direct RPM control, but only with the cyclic and pitch adjustments.
Because if you say that it's gone at 70, that actually suggests that the gain is simply too high.
Did the "shaking" only disappear at 70 or did it also go away with higher gain?
Best regards
Flo
Hi Maurice,
interessant, darf ich Fragen warum vgov wenn du mit 0 Gain fliegst? Dann fliegst du ja quasi ohne direkte Drehzahlregelung sondern nur mit den Zyklischen und Pitch Zugaben.
Weil wenn du sagst dass das mit 70 weg ist spricht das eigentlich dafür dass einfach das Gain zu hoch ist.
War das "zittern" erst ab 70 weg oder ging es auch mit mehr gain?
Liebe Grüße
Flo
maurice.krause
11 March 2025 19:1111.03.2025 19:11
Hi Florian,
I fly the governor with 0 gain because, at higher sensitivity, I felt that the RPM was being regulated too much, meaning that more RPM was being given. This made the helicopter seem a bit unpredictable to me. I couldn't find anything really good about it, so I switched it to 0 and simply flew with the cyclic and pitch adjustments. I liked that so far with the 700 and 600 models, so I've kept it that way.
Regarding the tail sensitivity, it's difficult to explain; during some flight maneuvers, like in the short video or Tic Toc's, it starts to twitch, at 70 it's gone, at 77 it twitches.
However, I'm still wondering, couldn't I just set the gain to 70 and let the optimizer run? That should improve things, I think, because of the locking mechanism, right?
Greetings
Maurice
Hi Florian,
ich fliege den Gov mit 0 Gain weil, ich hatte bei höherer Empfindlichkeit das Gefühl, dass die Drehzahl zu sehr geregelt wird, also im Sinne das mehr Drehzahl gegeben wird, dadurch wirkte der Heli für mich ein bisschen unzurechenbar, ich hab nicht wirklich gutes dazu gefunden, weswegen ich ihn mal auf 0 geschaltet habe und einfach nur mit den Zyklischen und Pitch Zugaben geflogen bin, das hat mir bisher beim 700er und 600er gut gefallen, deswegen habe ich das beibehalten.
Bei der Heck Empfindlichkeit, ist es schwer zu erklären, bei manchen Flugmanövern, wie im kurzen Video oder Tictoc´s fängt es an zu zucken, bei 70 ist es weg, bei 77 zuckt er.
Was ich mich jedoch gerade noch frage, kann ich nicht einfach mal Gain auf 70 stellen und den optimizer einfach laufen lassen? Das sollte sich doch dann denke ich verbessern, wegen dem einrasten oder?
Grüße
Maurice
maurice.krause
11 March 2025 19:5911.03.2025 19:59
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> Difficult to answer, 'it could be anything' :-)
>
> . Antistatic (installed, OK)
> . Servo
> . Cable/plug
> . Motor/controller (cable/insulation/short circuit to ground, one
(You can also see the twitching at the rear)
> . other electrical effects (peaks)
>
I tried to find logs, but... nothing.
> the cloud.
>
> Greetings
>
> Eddie
Hi Eddi,
It would also be good if I activated the cloud service; I've left Vbar Control on for a few minutes now, I hope you find something useful.
Greetings
Maurice Krause
Eddi E. aus G. schrieb:
-------------------------------------------------------
> Moin,
>
> schwer zu beantworten, 'kann alles sein' :-)
>
> . Antistatik (verbaut, OK)
> . Servo
> . Kabel/Stecker
> . Motor/Regler (Kabel/Isolierung/Masseschluss, ein
> Zucken da sieht man auch am Heck)
> . andere elektrische Effekte (Spitzen)
>
> Ich habe versucht, Logs zu finden, aber ... nix in
> der Cloud.
>
> Grüßle
>
> Eddi
Hi Eddi,
wäre natürlich auch gut wenn ich den Cloud Service aktiviere, hab die Vbar Control jetzt mal ein paar Minuten angelassen, ich hoffe du findest etwas brauchbares.
Grüße
Maurice Krause
florian_neuner
11 March 2025 20:0711.03.2025 20:07
How did you configure the governor? Or did you just fly with the default settings?
Because if you don't have proper engine speed control, the rear end won't handle perfectly during load changes.
That's why I would perhaps start there.
The optimizer doesn't directly affect the detent behavior; you could try experimenting with the stop gains. You could also try leaving the gain as is and lowering the P value slightly to see if that makes a difference.
Best regards
Flo
Wie hattest du denn den Gov eingestellt? Oder bist du einfach mit den Standard Settings geflogen?
Weil wenn du natürlich keine Ordentliche Drehzahlregelung hast ist das Heck bei Lastwechseln auch nicht perfekt.
Deswegen würde ich evtl. da erstmal ansetzen.
Optimizer hat jetzt nicht direkt was mit dem Einrastverhalten zu tun, da könntest du dich höchstens mal noch mit den Stop Gains spielen. Du könntest evtl. auch mal noch das Gain so lassen und dafür den P wert etwas runter stellen und schauen ob das was bringt
Liebe Grüße
Flo
maurice.krause
11 March 2025 20:3511.03.2025 20:35
Hi Florian,
I'll test it out in the next few days and get back to you.
Thanks for the help.
Greetings
Maurice
Hi Florian,
ich werde das mal die Tage testen und mich nochmal melden.
Danke erstmal für die Hilfe.
Grüße
Maurice
Eddi E. aus G.
12 March 2025 09:0512.03.2025 09:05
Good morning,
What is noticeable is that the controller is regularly fully open (100% PWM).
The rotational speed drops significantly.
This isn't regulation anymore, this is American-style chaos: full throttle, and let the battery handle it...
I would try loading the standard 700 setup, only re-entering the basic settings (e.g., trims), using the electric governor without changing anything, doing a trim flight, an optimizer flight, and then looking at/comparing the results.
Pilots' setups are often optimized for their needs/flying styles with their specific components, which doesn't always work well.
I've had some really extreme customer requests, everything's crap, setup by so-and-so, I can't fly like that... basic setup, OH! ... tweaked it a bit more, happy.
Then you can still see what the Pro Pilot may have adjusted, and try/compare individual settings in one or two banks.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
also was auffällt ist, dass der Regler regelmäßig voll offen ist (100 % PWM).
Die Drehzahl bricht dabei ein.
Das ist keine Regelung mehr, das sind amerikanische Zustände, Vollgas, und lass es den Akku regeln ...
Ich würde ja versuchsweise mal das Standard-700-er Setup laden, nur die Grundeinstellungen (bspw. Trimmungen) wieder eintragen, Elektro-Governor ohne was zu verstellen, Trimmflug, Optimierer-Flug, und dann schauen/vergleichen.
Setups von Piloten sind oft für deren Bedürfnisse/Flugstile mit deren Komponenten optimiert, das passt dann nicht immer.
Hatte schon ganz extreme Kundenanfragen, alles Sch***e, Setup von dem-und-dem, ich kann nicht so fliegen ... Grundsetup, OH! ... noch ein bisschen dran gedreht, glücklich.
Dann kann man immer noch schauen, was der Pro-Pilot ggfs. angepasst hat, und in einer oder zwei Bänken einzelne Einstellungen probieren/vergleichen.
Grüßle
Eddi
Born to fly ...
forced to work.
maurice.krause
13 March 2025 07:1813.03.2025 07:18
Hi Eddi,
I'll give that a try; I directly transferred the NEO setup to the EVO, so to speak. I now understand that it doesn't make much sense. If the weather permits, I'll try it out today.
Regards, Maurice
Moin Eddi,
das werde ich mal machen, ich habe direkt das NEO Setup sozusagen auf das EVO übernommen, verstehe jetzt auch, dass das nicht so viel Sinn macht, wenn das Wetter es zulässt, werde ich es heute mal ausprobieren.
Gruß Maurice
maurice.krause
13 March 2025 12:5213.03.2025 12:52
Hello everyone,
Yes, look at that, new setup, trim values adopted, trim flight performed, optimizer maxed out, tweaked the sensitivities and maneuverability a bit, and bam, everything's great, or almost...
I still have the problem that it easily takes 5-6 seconds before the motor starts to turn, so I flip the switch, put the pitch stick fully positive, wait 5-6 seconds and then it starts turning.
I selected Vgov again, telemetry to the Hobbywing 200A is working.
I still have dangerous vibrations, but the helicopter isn't causing any problems in that regard.
But otherwise I have to thank you, the 700 is now flying really well in principle.
Greetings
Maurice
Hallo zusammen,
ja siehe da, neues Setup Trimmwerte übernommen, Trimmflug gemacht, Optimierer ausgereizt und bisschen an den Empfindlichkeiten und Wendigkeiten gedreht und zack, alles Top, zumindest fast...
Ich hab noch das Problem das locker 5-6 Sekunden vergehen bis der Motor anfängt zu drehen, also Schalter umlegen, Pitchknüppel voll Positiv, 5-6sek warten und dann dreht er erst an.
Ich habe wieder den Vgov ausgewählt, Telemetrie zum Hobbywing 200A geht.
Ich habe auch immernoch Gefährliche Vibrationen, aber der Heli macht jetzt keine Probleme dies bzgl.
Aber sonst muss ich euch danken, der 700er fliegt jetzt prinzipiell echt gut.
Grüße
Maurice
Eddi E. aus G.
13 March 2025 13:2013.03.2025 13:20
Hi,
glad to hear.
Pitch stick fully positive, why? The ramp-up has nothing to do with it, please always ramp up at approximately 0°.
I'm not that familiar with WobbyHing, but perhaps the motor-off point in the setup can be used to better align the two points where the VBar starts its ramp-up and where the controller kicks in.
_Actually_, this should happen in a coordinated manner if you adjust the controller via telemetry...?
Perhaps Rainer has another idea?
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
freut mich, zu hören.
Pitchknüppel voll positiv, warum? Der Hochlauf hat damit nix zu tun, bitte immer mit etwa 0° hochlaufen lassen.
Ich bin mit WobbyHing jetzt nicht so vertraut, aber vielleicht kann man über den Motor-Aus-Punkt im Setup die beiden Punkte noch besser zusammen bringen, wo die VStabi mit ihrer Hochlauf-Rampe beginnt, und wo der Regler anspringt.
_Eigentlich_ sollte das koordiniert ablaufen, wenn man den Regler über die Telemetrie einstellt ..?
Vielleicht hat Rainer noch eine Idee?
Grüßle
Eddi
Born to fly ...
forced to work.
RV
13 March 2025 14:3113.03.2025 14:31
If the hardware is programmed using our telemetry, there is no delay.
Try this:
Scroll down in Model Setup, then select the Gov Art, the HW menu will appear - and click.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Wenn der HW mittels unserer Telemetrie geproggt wird gibts da kein Delay.
Mach mal folgendes:
In Modell Setup runterscrollen, dann die Gov Art auswählen, das HW Menü kommt hoch - und klicken.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
13 March 2025 14:3613.03.2025 14:36
Hi,
Thanks for the reply, I'll test/check it tomorrow, it's pouring rain here.
Greetings
Maurice
Hi,
danke für die Antwort, werde ich morgen mal testen/schauen, bei uns schüttet es wie aus Eimern.
Grüße
Maurice
maurice.krause
28 March 2025 15:5328.03.2025 15:53
RV wrote:
-------------------------------------------------------
> If the hardware is programmed using our telemetry
There will be no delay.
>
Try this:
>
> Scroll down in Model Setup, then select Gov Art
> select, the HW menu will appear - and click.
Hi Rainer,
I haven't had a chance to test it properly lately. In Gov Art, I selected HW (hardware). I can also configure the HW settings; it's configured exactly the same as my Logo 600, which turns on immediately. Do you have any other ideas what the problem could be?
Greetings
Maurice
RV schrieb:
-------------------------------------------------------
> Wenn der HW mittels unserer Telemetrie geproggt
> wird gibts da kein Delay.
>
> Mach mal folgendes:
>
> In Modell Setup runterscrollen, dann die Gov Art
> auswählen, das HW Menü kommt hoch - und klicken.
Hi Rainer,
bin die Zeit über nicht zum testen gekommen, bei Gov Art hab ich HW ausgewählt, ich kann auch am HW was einstellen, es ist genauso konfiguriert wie bei meinem Logo 600, da geht er direkt an, hast du vielleicht sonst noch Ideen woran es liegen könnte?
Grüße
Maurice