← Logo 700 and 800

Logo 700 Setup translated

Mikado Model Helicopters › Logo 700 and 800 · Started by HP on 7 June 2025 18:4707.06.2025 18:47
HP 7 June 2025 18:4707.06.2025 18:47
Hello everyone!

I'm interested in the new Logo 700, but I'd like a specific setup for the longest possible flight time. Unfortunately, I have no idea what would be suitable. Flight time should be around 10 minutes, or even more. Which motor, ESC, battery, and pinion gear would you recommend?
I'd like to use a YGE ESC with BEC, possibly with a Mikado backup if needed. The motor might be a Scorpion or X-Nova, 10S or 12S. No hardcore 3D flying, just basic aerobatics. But not exactly low RPM either.
Please send your suggestions!
machine-translated from German · Show original
maurice.krause 8 June 2025 10:3408.06.2025 10:34
Hi,

I think the 4525-530 or 560kv from Xnova would work; you can fly the 530 with a 14-tooth pinion, but the 560 is better with a 13-tooth pinion. However, 10 minutes will be challenging, depending on how much power you need.

I fly with 5100mAh 55C 12s batteries at 9000W / 190-200A for about 3 minutes. The speed controller doesn't really affect how long you can fly. A Mikado backup is highly recommended.

I would then choose batteries that perhaps don't have such a high discharge rate, but one of the Mikado people can certainly help you much more with that.

Greetings
Maurice
machine-translated from German · Show original
Eddi E. aus G. 10 June 2025 07:0410.06.2025 07:04
Good morning,

I would then design the helicopter with a 12S battery for about 1,500 RPM at 80% throttle, a 450kV motor with a 13 or 14-tooth pinion gear (approx. 1,450–1,550 RPM; experiment), and lightweight batteries. RPM is the biggest energy consumer due to air resistance. If the ESC had an adjustable current limit (without cutting out), that could also improve things. Performance would still be comparable to a good internal combustion engine, and flight time would be good.

10s with a 560 should also work.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
HP 10 June 2025 21:1910.06.2025 21:19
Hello Eddi!
I think we're on the right track. Which engine would be better suited? A 4035 or a 4525?
X-Nova would offer both with 480 kv.
That's what I thought, around 1500-1600 rpm should be enough for the 700.
machine-translated from German · Show original
Eddi E. aus G. 11 June 2025 08:3711.06.2025 08:37
Good morning,

Phew, no idea. Presumably the smaller motor would suffice (with current limiting and/or good cooling; we experimented with that years ago), but I'd probably go for the larger one.

The 'problem' is, even if it flies great, is quiet, long-lasting, and cheap to maintain, hardly anyone wants that; it's only ever measured by ever more performance...

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
copter 11 June 2025 22:0511.06.2025 22:05
Hello

I fly my 700 Logo with a 12S 5000mAh battery.
RPM around 1600-1700.
Kontronik Pyro 750-56 motor
Kosmik 160HV controller

With this setup, I get a flight time of between 8-10 minutes.

During simple aerobatics.

Greetings Copter
machine-translated from German · Show original
HP 13 June 2025 20:2913.06.2025 20:29
Hello everyone!
Thanks for the replies! @Copter, that sounds good, it's pretty close to what I have in mind. Now I have a starting point. Which pinion gear are you using?

@Eddi, that seems to be the current trend; I'm less interested in hardcore 3D shooters now that the show's over in 3 minutes. Unless you have 10 batteries and 3 or 4 chargers with you ;-)
machine-translated from German · Show original
copter 13 June 2025 22:2813.06.2025 22:28
Hi

I'm flying with a 14-tooth pinion gear.
Of course, higher rotational speeds and wild 3D maneuvers will reduce the flight time.
Even though I'm not exactly traveling at a leisurely pace, I can still achieve these flight times.

I only have one battery, as we have a power connection at the airfield.

I charge at 2C, so the battery is fully charged again in about 20 to 25 minutes.

Greeting
machine-translated from German · Show original
Eddi E. aus G. 16 June 2025 09:2816.06.2025 09:28
Good morning,

Of course, you can also fly at low RPM with a standard motor, and (with appropriate power requirements and flying style) you'll achieve the corresponding flight times. Ultimately, you simply need a certain amount of power, a specific number of watts, relatively independent of the motor configuration. Air resistance (RPM, pitch) are the real obstacles.

The only potential problem is that you then fly with a relatively low controller opening, practically at idle, and if you then fly more power-oriented for a longer period (wide aerobatics, but with some thrust, large loops with a lot of pitch and little yaw, for example), corresponding currents flow at low PWM, and the controller and motor may get hotter, possibly leading to shutdowns or damage.
The power is potentially there, and electric drives tend to draw it, if necessary up to the stall current, if there is no effective (also: cool-running) current limiting.

Some controller manufacturers (e.g., YGE) only activate the governor when the controller is open to 50% or more, based on experience.

The advantage, if you fly it accordingly and don't overload it, is that you can fly Country and Western however you feel like it.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Racetom 25 June 2025 18:4425.06.2025 18:44
Hello,

Is there any information yet on when the new Logo 700 will be available and how much it will cost? We've already had summer, after all :-)


Best regards,
Thomas
machine-translated from German · Show original
Rolf Rakette 26 October 2025 11:3326.10.2025 11:33
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> Of course, you can also use the normal setting for low RPM.
> Propulsion for flying, achieved (with appropriate
(Performance requirements, flying style) then also the
> corresponding flight times. In the end, you need...
> 'Simply' a certain level of performance for that,
> so many watts, relatively independent of the
> Drive system design. The air resistance (speed,
> Pitch) are the 'enemies'.
>
The only problem _could_ be that then
> flies with a relatively low throttle opening, practically
> at idle, and if you do it for a longer period of time
> more performance-oriented flying (wide-range aerobatics,
> but it does involve a train, big loops with lots of...
Pitch and a little bit of Nick, for example), flow into
> lower PWM corresponding currents, and controllers
The engine and motor may get hotter, possibly up to...
> Disconnections or damage.
The potential performance is there, and
Electric drives tend to pull, in
Doubts leading to a stalled current, if there is no
> effective (also: cool-running) current limiting
> exists.
>
Some controller manufacturers (e.g., YGE) activate the
> Governor, for example, only activates from 50% throttle opening onwards,
> from experience.
>
> Advantage if you fly it accordingly and not
> Overloaded: you can fly Country and Western,
> Whatever you feel like doing.
>
> Greetings
>
> Eddie

Hi Eddi, :-)

I've also built myself a low-RPM system...

XNOVA motor with 380KV and 13-tooth pinion.

Leave the 710s out of your hands.

Engine speed around 1200 rpm or slightly below...

YGE 105 ESC on a 12S 5000mAh battery. ESC opening around 70% :-)

I set it up in between other things.

Flies great, worked well from the start without needing to trim anything.

The speed controller and motor remain almost cold. Under normal flying conditions, the current draw is a maximum of 16A, while at full pitch it's around 30A...

After 10 to 12 minutes, the 5000 battery is half empty or half full.

It's a shame that these parts are no longer available.

The Mikados fly and fly with almost no maintenance.

And you can do anything with them :-)



Edited once. Last edited on 26.10.2025 at 11:34 by Rolf Rakette.
machine-translated from German · Show original
Eddi E. aus G. 27 October 2025 09:3527.10.2025 09:35
Good morning,

Sounds great :-)

This also fits into the picture with Uli's 690 low RPM, which flew at around 1,000 rpm and I think also 12s 5,000 for what felt like half an hour of smooth, round 3D.

That will also be possible with the new 700 series :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Rolf Rakette 27 October 2025 17:5127.10.2025 17:51
Hi Eddi,

Initially, I had some problems with the Mikados....

I think they're great now; all of mine have run all year without any problems...

And they're all quite quiet, even colleagues from the club agree!!

The revs drop really well and they're quite durable, in my opinion.

The 550 tipped over once while landing, I simply righted it and continued flying.

I did practically nothing to it, just a little grease to the main gear, nothing more... And they were also in

Rain in full sun, no problem at all...

I'm glad to hear that it will work again with the "new" one...

I think waiting is definitely worth it!! What was that saying again? Rome wasn't built in a day, was it?!

By the way, I think the rear-wheel drive makes most of the noise... Couldn't it be done with rear-wheel drive too?

Paleoid gears made of superplastic?? I think it can really withstand a lot.

The question is, could one make a suitable tool? :-)

Just a thought... And if possible, use as many identical parts as possible :-)

Greetings
Rolf
machine-translated from German · Show original
Eddi E. aus G. 28 October 2025 09:0228.10.2025 09:02
Hi Rolf,

A lot has already been changed at the rear. Whether it's quieter in the end is hard to say, because the guys are really pushing the helicopter to its limits to test its stress and wear... which tends to make it rather loud.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
flydown 28 October 2025 10:3828.10.2025 10:38
Attention (wink):
You should pursue the SAB strategy.
First, I need to get the helicopter out; I'll never reach its limits with my extended circular flight anyway.
And if any abnormalities occur, a highly important upgrade follows.

Autumn greetings
Uwe
machine-translated from German · Show original
Eddi E. aus G. 28 October 2025 11:1328.10.2025 11:13
Hi Uwe,

Even with ;-) meaning 'the customers' want the beta test to take place with them?
Fascinating ^^
Man... then we could have released it in the summer after all :-)

Grüßle ;-)

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
flydown 28 October 2025 15:2128.10.2025 15:21
...I would have taken one... 8-)
machine-translated from German · Show original
Eddi E. aus G. 28 October 2025 15:5428.10.2025 15:54
Hi,

The snake is on the left ^^ :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Rolf Rakette 28 October 2025 19:1128.10.2025 19:11
You Eddie Snake sounds good :-)

In the past, some high-end helicopter manufacturers did things quite differently.

There were waiting lists in advance because there was only a certain number of kits available!

Furthermore, I believe a deposit was also requested :-)

Of course, everyone wanted to be on the list, to be at the very top, if possible.

The construction kits were supposedly always sold out.

The price also remained consistently high.

So, according to the supply and demand method, eh 8-) .

If you had good connections, you could also get one outside of the regular schedule :-)

Perhaps that's something to consider?

I know I'm being mean, but that's how it was back then too :-)

Greetings
Rolf
machine-translated from German · Show original
Eddi E. aus G. 29 October 2025 08:5829.10.2025 08:58
Good morning,

Oh, why evil?

Everyone does it differently.
Hopefully, the finished product will be convincing in the end :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Rolf Rakette 3 November 2025 18:1803.11.2025 18:18
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> Oh, why evil?
>
Everyone does it differently.
Hopefully, the finished product will ultimately be convincing.
:-)
>
—Eddi

Good evening Eddi, ;-)

Then I prefer your way. ;-)

Since I still have plenty of Mikado sticks, I can easily wait. :-)

And if they're as good as the "old" ones, or even better, then everything's fine, I think. 8-)

I think some of the Chinese models will be off the market by now. :-)

See you later, greetings
Rolf
machine-translated from German · Show original
Bernd S. 7 March 2026 08:5507.03.2026 08:55
Cheers to coffee...

I'm following along with interest - I'm planning a SLOW upgrade - but I haven't worn out many things yet when everything needs to be replaced.

The new 700 would fit - if I go with 12S and want to continue using the existing motors (Pyro 700/520 & Scorpion 4035/520), it seems doable with a 14-tooth pinion - ESC YGE Aureus 105 (135 probably not necessary?).

I don't like hard 3D (I can't do it either) - but powerful, wide-ranging aerobatics - that's nice, and others will soon like it more than the shooting - and for shooting, there are others in the club who can do that.

Normally I get 14-18 minutes – and that's not at low RPM (10S 4500-5000mAh) – the 10S stick batteries are practical, but somehow they're "going out of fashion"? Recharging isn't a problem since I have over 3kWh of power supply batteries (homemade LiFePO4 26V) for charging at the field – and that works easily with the old Schulze charger at 2C and more than 8 charges – solar buffered if necessary.

Okay, I've written too much – the important question is: Would motors with a 14-tooth pinion on an Aureus 105 with 12S be practical on a new 700 with 700 standard blades, etc.?

So, let's settle comfortably into the present – and like others here, I don't necessarily see Mikado as cheap, BUT when I see what's become of my colleagues' other helicopters? -> My Logos are still flying perfectly. That's (how do they phrase it these days) sustainable :-) & true value – worth the price -> good value!

The weather will be usable - time to fly again (and surely tomorrow in Halle with Logo 200).

Bernd
machine-translated from German · Show original
Eddi E. aus G. 9 March 2026 09:1109.03.2026 09:11
Good morning,

The engines are geared more towards economy than maximum performance, but that doesn't seem to be the goal anyway.
Therefore, it should work well, even with the Aureus 105.

Possibly also with the 13-tooth sprocket if maximum speed is not the goal.

When adjusting the speed and pitch, you can make sure that the 'fighting speed' (which will then result in approximately 1,800 rpm with the 13-inch motor and 1,950 rpm with the 14-inch motor) does not drop significantly, especially towards the end of the battery life, or that the controller still has room to adjust.

That's a rather conservative calculation, based on flight time and engine displacement, not on three minutes of full throttle, which would then be around 2,200 to 2,300+ rpm, but then you would also need the 45-class motors to handle that (pitch and brutal flying style), and a correspondingly more powerful controller.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Bernd S. 10 March 2026 06:3210.03.2026 06:32
Hi Eddi,

Yes - more economically or realistically - I (and others) don't exactly have money to burn - so it has to "pay off" - and since I'm over 55, hardcore 3D is no longer realistic or (as already mentioned) not my thing.

And after inspecting the existing logos, I'm planning my future - and that includes upgrading one of the old ones to VBar Evo with YGE controller and then with the VBar control transmitter (we've already discussed that).

But also the option of being able to use components in the new 700 - on the other hand, not buying components that are then undersized in the 700 - a slight drop in revs would be perfectly acceptable (for me).
The logical choice would be a larger motor and an Aureus 135 - but realistically, I'd use my existing motors with an Aureus 105 - a new 700 would then sensibly get HV servos - the motor could always be upgraded later if needed - I see the old servos (which are still in great condition (Futaba BLS451/452/251)) as obsolete and a risk due to age rather than the motor power.

Therefore (something off-topic here) the 600SE will soon be modified like this - it runs nice and quietly and I think it will get me further the fastest - and Jive80HV against Aureus 105 as well as MiniVBar against Evo also fits in terms of effort.
The Aureus 135 would of course be even better - I'll think about it some more; the decision will be made this weekend.

And the biggest competition for the logos is our own older generation - they fly so perfectly that only a few can use the difference (certainly not me).

Greetings

Bernd
machine-translated from German · Show original
Eddi E. aus G. 10 March 2026 09:1410.03.2026 09:14
Hi Bernd,

Everything fits from my point of view :-)
I wouldn't have any major concerns about the BLS either.

Of course, you can only achieve the maximum with the maximum effort: 12V servos + suitable controller for the best implementation of what VBar EVO can do, 'fat' motor and controller for best performance (our specialists have also flown the 700 with 13 and 16s... wow!).
And pushing the limits, or rather, enabling pilots to push them to the limit if they want to, is also part of our motivation.

But solid 'normal' equipment is always a good choice, even if you get laughed at by some advertising victims :-) ^^

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless