← Logo 400 ... 690

Logo 600 SE setup

Mikado Model Helicopters › Logo 400 ... 690 · Started by carlesps on 27 April 2024 19:3427.04.2024 19:34
carlesps 27 April 2024 19:3427.04.2024 19:34
Hello,

I have a Logo 600 SE and when main rotor is spooling up tail makes a sharp turn of about 45 degrees to the right and then stabilizes, the variator is configured with soft start. Should I increase the tail gain to avoid this?

Thank you,
Carles
RV 27 April 2024 19:4927.04.2024 19:49
Well - let us know more.

- Which ESC is used in which mode?
- Which gov mode is used in VBar?
- How is the motor being turened on? Is there some "safety switch" in the game, does the "Motor" switch have probably a momentary position? How are they handled when starting the model?

If VGov is used - attach screenshots of the values in flight panel

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
carlesps 27 April 2024 20:4327.04.2024 20:43
Hello,

I am using HobbyWing 120A pro whith vbar governor and there is a motor-on switch with 3 positions, off, idle and on. I switch to on to start with bank 1 selected.

I have attached a pdf file whith vbar gov setup.

Thank you very much,
Carles Attachments:
open | download - Logo 600 SE gov.pdf (174 KB)
RV 27 April 2024 22:0527.04.2024 22:05
Okay - so the switch handling is ok here like mine and recommended.

But - i think it is the ESC. Let me explain:

Using VGov our Spec says there is a "jump" in throttle to turn on the motor as a kind of "safe" signal. Then the ESC should turn the motor on, spool a bit up and fade over to our throttle signal slowly when the motor runs correctly.

Obviously this fading process isn't working, it seems to be a kind of switch instead.

As i didn't have this on my V5 HW ESC here - is it a V4 probably?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




Edited 1 time(s). Last edit at 04/27/2024 10:06PM by RV.
carlesps 28 April 2024 07:3328.04.2024 07:33
Yes, it is V4 with vbar firmware.

Thank you,
Carles
RV 28 April 2024 09:0828.04.2024 09:08
OK - one last thing - how is the throttle endpoints in the VBar? - It should be +-100% here.

if this is ok - i am sorry - we can't do anything here.

Just check if the ESC is updated - and probably update it. If this won't help - it is still the known issue on the V4's - either claim at HW or use as it is or use in HW ESC gov mode.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G. 29 April 2024 09:0529.04.2024 09:05
Hi,

a couple more questions, please: does the drive spool up, with a shapr jump, or soft somehow?

When the model is standing on the ground, ready to spool up, do you center the tail rotor (there are sticks for that on your transmitter ^^), or does it maybe stand a full left or full right, because the model was moved from preparation to takeoff?

Kind regards

Eddi

Born to fly ...
forced to work.
florian_neuner 29 April 2024 10:1629.04.2024 10:16
Hi!

i have had "the same" with my old 160a v4 HW Escs running vBar Governor. In your Governor settings try lowering the Runup Limit to 2 instead of 3. This should slow down the Spoolup and minimize the "tail kick".

Regards

Florian
RV 29 April 2024 11:0029.04.2024 11:00
If you just want to have a fix for your spoolup behaviour - lowering Acceleration and Gain is probably the way to go as Florian recommended.

But - Acceleration slows down the complete spoolup then - and also - the AR Bailout recovery. Gains slow down the reaction of the Gov itself in common.

So - if it is ok for you then, no problem, but technically the wrong end to deal with ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
carlesps 29 April 2024 13:0629.04.2024 13:06
Hello,

Thank you all, I really appreciate your help, next weekend I am going try Florian tip.

Best regards,
Carles
VStabi VStabi Pioneer of Flybarless