← Logo 400 ... 690

Logo 550 SX Maximum Main Blade Pitch

Mikado Model Helicopters › Logo 400 ... 690 · Started by Razmo on 6 June 2024 01:2106.06.2024 01:21
Razmo 6 June 2024 01:2106.06.2024 01:21
Hey Guys,

Any reason I can't or shouldn't configure my main blade pitch to 16/16?

Thanks,
Raz
RV 6 June 2024 06:2706.06.2024 06:27
Well ... you need to consider the cyclic too.

For example:

If you do a maneuver with full collective and full cyclic - there should be enough reserve before the blades get into a stall. I have watched this many times in fast forward flights when there was no headroom anymore to keep the helis nose down. It just boomed up suddenly due the stall effect on the backwards moving blade. There is aparameter where a headroom can be set to avoid this - it must be altered then according to the help in the VBC. But it can also not work when exceeding physical limits.

Another thing is - could the power drive (motor, ESC, Gear etc.) handle this for a longer time.


If i would have the need - i would start at 14 first and test some days - then decide if 15 is needed and possible.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bernhard Kerscher 6 June 2024 07:0206.06.2024 07:02
Good morning,
I built a Logo 550 for speed flying out of interest.
The Logo runs with the original M0.7 gear and is powered by an Xnova 4025 and the whole thing with a z16 pinion.
At the moment I am flying the Logo at 15.6°/9° pitch, but the motor is already at its limit and can only just keep the speed at 2250RPM.
The gear has held up for many flights, but here it is only with a constant load.
I can't imagine that it will hold up for aerobatics and I don't think you need it.
I also have a light L550 that I fly with 13° pitch for aerobatics and that is more than enough for me.

Regards Bernhard



Edited 1 time(s). Last edit at 06/06/2024 07:03AM by Bernhard Kerscher.
Razmo 10 June 2024 19:2510.06.2024 19:25
Hi Guys,

Appreciate the information here. I have the desire to go 16/16 for a couple reasons. One is to simply set for auto's. I've never set pitch for auto's as I've never flow heli's larger than a 550. I do intend to go 700 here soon. Would you suggest a total travel setup of 16/16 for auto's here on the 550?

The second reason is a bit more complicated as it has to do with not understanding how pitch curves work with the VControl Touch EVO. I'm not understanding why it's only 5 point or why I can't move points on the curve. I'll explain and create another thread on this topic.

Thanks,
Raz



Edited 1 time(s). Last edit at 06/10/2024 07:26PM by Razmo.
Bernhard Kerscher 11 June 2024 08:5211.06.2024 08:52
Hello,
how you set your pitch values is up to you.
I, for example, fly the same pitch setting in all flight modes.
Other pilots fly different pitch values ??at different head speeds.
If you don't know that and are perhaps a beginner, I would leave the pitch values the same to start with.
But I still think 16° is too much.

On the subject of the pitch curve, why would you need more than 5 points?
The pitch curve is usually a straight line in a 3D model anyway and it doesn't matter how many points it consists of.

Rainer can certainly give you more information about the radio.

Greetings, Bernhard.



Edited 1 time(s). Last edit at 06/11/2024 08:53AM by Bernhard Kerscher.
Eddi E. aus G. 11 June 2024 09:2611.06.2024 09:26
Hi,

same here, same collective values (like 12-13° symmetric) for all models, for all flight conditions.

The higher the angle of attack, the higher the aerodynamic drag, the easier it is to bleed off kinetic energy, head speed, which you have available only once anyway.

În practice, in an autorotation, you use only little collective to control the descent.
You hear the main rotor speeding up or loosing rpm (don't practice from scratch when all nitros are up in the air ... you need the acoustic feedback!).
Maintain a steady descent, and do it into the wind.

When you come down to 4-3-2-1 m, you flare, using cyclic to slow down to a stop, e.g. tilt the rotor disk backwards, and also again only little collective to control the final descent.

Practice with low head speeds first (e.g. bank 1 only 1,000 1/min or such), be prepared to abort.
When switching to Motor Idle (switch center position), the motor will still run at a low rpm, so it's ready to spool up again quickly if you want to, need to abort.

Honestly, even though I've never been a a fan of autorotations, and not very proficient for that reason, I'd dare say no one needs 16°.
I can understand that you'd want to increase—a bit—if you run a large and heavy scale helicopter, which has more kinetic energy in it's larger rotor disk, to give you a small reserve. Like, from + 9-10° to + 10-11-12°.
But if you time it wrong, the heli turns piano ... no matter what collective angles you have set.

My some cents :-)

—Eddi

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless