Freeskiken
24 October 2025 05:1124.10.2025 05:11
Hi, I was helping a fellow pilot today with his Logo 600SE V2. This helicopter was purchased from Mikado in Germany through a local shop, The Heli Hanger & Hobby here in Canada. This helicopter does not have very many flights on it. It is really like new. It has never been crashed or abused. Trying to troubleshoot the problem he decided to put new bearings in for the main shaft and a new main shaft but nothing changed.
I also had been dealing with a freind in the USA with the same issue. He changed gears, bearings, shafts, blade grips etc, etc. trying to eliminate this problem.
The issue is a really bad shake at 1550 to 1650 rpm. Below this at 1460rpm it is perfect, at 1740rpm it is better maybe just a tiny tiny bit, but acceptable. I tried differant head gains. He tried V8 and then went back to V7. but it is still there.
I have been talking to my freind in the USA about the same problem and untill I saw it first hand I didn't really realize how bad the shake is.
So is this just something they both have to live with ? is there a reason that you know of ?
They have both spent a great deal of time and money trying to repair this to no avail.
flydown
24 October 2025 06:0724.10.2025 06:07
Hello,
Have you checked for vibrations? I once experienced this phenomenon due to vibrations coming from the engine.
Regards, Uwe
Eddi E. aus G.
24 October 2025 09:1024.10.2025 09:10
Hi,
those 100 rpm are probably a resonance area where there's not much you can do but decisively alter the dampening, e.g. put the rubber rings on a drill, spin them, and abrade them. Then clean them, lube them, put them on again.
I had mine set up for 1.400, 1.600, 1.850, and it was just well (years ago, though).
What also helped me, occasionally, with wobbles which were more pronounced at certain rpm than at other (or totally gone at even slightly higher rpm) was what we in Germany call 'Schlüter magic tape', after one of the inventors of the r/c model helicopter in the late '60s of the last millennium, Dieter Schlüter. Means, put a strip of electrical tape on one of the blades, approximately in it's COG lengthwise, try. If it gets worse, try the other blade.
Of course all other bases should be covered (COG of the model, center or slightly front), blade tracking, shafts running true etc.
And another thing which I encountered with a different .60/700 size electric way back in time was, it was bobbing on the elevator axis, the bobbing changed with rpm, but was not curable. At some point I changed the tail blades, and ... the bobble was gone, instantly. I wasn't even suspecting them not running true or not being balanced. But sometimes the cause lies not where you'd look first, is what I learned from it.
—Eddi
Born to fly ...
forced to work.
Freeskiken
24 October 2025 14:4324.10.2025 14:43
Quote: those 100 rpm are probably a resonance area where there's not much you can do but decisively alter the dampening, e.g. put the rubber rings on a drill, spin them, and abrade them. Then clean them, lube them, put them on again.
Sorry in translation. What is “abrade” ? Sand the outside diameter of the damper O rings ?
I have a blade balancer. So I could try that. But I am sure my friend in the USA tried that on his Logo 600SE. And also tried other main and tail blades. But the same shake at 1550 to 1650 rpm occurred.
Freeskiken
24 October 2025 14:4924.10.2025 14:49
I will look at the CG and try different main and tail blades.
Unfortunately it is getting near the end of the season. So not much time for me to help him. Until maybe next year. He is frustrated and says he will probably sell the helicopter. Maybe I can help him.
I have all the new parts to build a Logo 690. So that is my winter project. I hope there is not the same issue. I was planning on flying it at 1550 to 1650 rpm on a Pyro 700-56 competition motor on 8S batteries.
Eddi E. aus G.
24 October 2025 15:1024.10.2025 15:10
Hi,
yes, sorry, sand off is probably the better term.
Since 'magic tape' has the word magic in it ;-) I'd do it even if the blades seem to be balanced well. It's weird that something if you think you unbalance something, you actually improve it. Doesn't cost much, doesn't take much time, but worth a try anyways.
With the LOGO 690, I recall Uli here runs it at as low as 1,000 1/min, or used to, and he also sanded off the rubber to adjust the dampening.
But of course also the actual weight has an impact on what dampening works best.
I recall when 'the Italian stallions' were nicknamed Wobble Gobble, because they were designed for (imo) insanely high head speeds and would always wobble at lower or low rpm.
If it was me, I would probably just avoid that head speed window and enjoy my flying, and leave fiddling with it to another time.
Best,
Eddi
Born to fly ...
forced to work.
Freeskiken
24 October 2025 19:3524.10.2025 19:35
That’s kind of what I was thinking. Avoid that rpm, and enjoy flying.
I will try the black tape and see what happens.
I was thinking that maybe running it on a 6S or 8S system and changing the motor to lighten the helicopter. Then it would be better at the low rpm.
Edited 1 time(s). Last edit at 10/24/2025 07:35PM by Freeskiken.
Freeskiken
24 October 2025 19:4124.10.2025 19:41
What power system was initially recommended for the Logo 600SE ? And what rpm ?
Eddi E. aus G.
27 October 2025 09:3127.10.2025 09:31
Hi,
the 600 SE (what I for myself nicknamed a stretch limo :-) was originally meant for a 10s setup (say 4,000 mAh) with a 560 kV motor or thereabouts, or 12s (3,300 mAh) with 450 kV.
Means, e.g. a Scorpion or other 80-120 A HV ESC was good, and the corresponding Scorpion 4035 (or similar size and kV depending on the cell count).
Auw then, depending on the components (motor, ESC, battery) beginning in the low 4 kg range.
Recommended max. head speed 1,800 which is (or was) already plenty for a lightweight 700 size.
With the introduction of the counter bearing with main shaft support, things went a bit northward, because the main gear became more protected against eventual flexing. I mean, it's originally a 600, which back then, before or at the dawn of competitive 700 sizes, was a competitive machine.
And it's still one of my favorites, good size, lightweight, precise, silent, almost maintenance-free.
But I'm not, and never was, the hard style 3D pilot.
The 700 XX, then, was a lot.
The new 700 was again just right (preferred it over the 690) even if I was never able to fathom its true potential.
Best,
Eddi
Born to fly ...
forced to work.
Vinger
3 November 2025 16:2703.11.2025 16:27
Here is the video explaining the sanding of the dampers
https://uroehr.de/vtube/cat/technical-support/video/low-rpm-dampener
Regards
Peter
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
flydown
6 November 2025 14:1606.11.2025 14:16
Hello,
why not trying dampeners of Logo 550?
Mine (550) and the one of a friend flies wobblefree down to 900 U/min.
900U/min
Or replace the middle O-ring with a 3D printed spacer, for example 8.5x13x2.5mm.
Motor you can use down to 4020,
Motor up to what fits in the mechanic and the one way can handle.
But I love seeing how people can experiment with the logos. :-)