{"ok":true,"content":"Unfortunately, micro-vibrations are involved. This occurs occasionally, especially with very rigid helicopters (e.g., TDR2).<br><br> If the helicopter is running well, you can use the standard initialization in the rescue mode; the only condition would be that you must not switch on the helicopter while it is lying down.<br><br> <a href=\"http:\/\/www.vstabi.info\/de\/V6_2\" target=\"_blank\" rel=\"noopener noreferrer\">http:\/\/www.vstabi.info\/de\/V6_2<\/a> - there&#39;s some information about it at the very bottom.<br><br> <a href=\"http:\/\/www.vstabi.info\/de\/node\/1944\" target=\"_blank\" rel=\"noopener noreferrer\">http:\/\/www.vstabi.info\/de\/node\/1944<\/a> also shown here on the screen.<br><br><br> The technical background is as follows:<br><br> We have installed two accelerometer sets to support rescue orientation: one in the IMU, a low-range set up to 15G (calibrated), and a high-range set up to 200G (uncalibrated). Upon power-up, the model&#39;s orientation is determined, and the high-range accelerometers are calibrated using the low-range set.<br><br> Due to micro-vibrations, the Z-sensor of the IMU (15G accelerator sensor) is driven to its limit and then gets stuck there.<br><br> This is irrelevant for the flight, as we switch to a second set of sensors (up to 200 G) immediately after takeoff due to the &quot;basic vibration level&quot;.<br><br> Normally, we initialize using all three sensors. If we detect that the Z-axis is stuck, a warning is issued in precision mode. You can fly, but you are not allowed to perform a rescue.<br><br> In standard mode, there&#39;s a fallback to X\/Y \u2013 Z is then calculated. However, the model must then be horizontally aligned by \u00b145\u00b0. If this is used, it will twitch three times. If Z is correct, it will twitch once. The recovery is safe.<br><br> Incidentally, we&#39;re the only ones who have the High Range kit installed... it&#39;s really expensive, but necessary. A Logo, for example, has 12 G vibrations while hovering, a 600cc nitro engine about 45, and a gasoline engine around 80 G ;-(<br><br> Addendum: since we also need the sensors here for the new lightness feature - in case of a Z-axis error, the lightness should be deactivated with &quot;0&quot; until the helicopter runs with sufficiently low vibration.<br><br> Uli gives a presentation on the topic of vibrations here:<br><br> <a href=\"https:\/\/uroehr.de\/vtube\/video\/v-tv-rotor-live\" target=\"_blank\" rel=\"noopener noreferrer\">https:\/\/uroehr.de\/vtube\/video\/v-tv-rotor-live<\/a><br><br> From about minute 42.<br><br> SAB has developed several gyro mounts specifically for Kraken to combat the vibration issues.<br>\n<br>\nregards (EN) \/ Gruss (DE) \r<br>\n\r<br>\nRainer Vetter\r<br>\n\r<br>\n_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ \r<br>\nPosting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.\r<br>\n\r<br>\nF\u00fcr Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollst\u00e4ndig abarbeiten. Nehmt Euch Zeit, beantwortet R\u00fcckfragen in Ruhe und vollst\u00e4ndig.\r<br>\n_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ \r<br>\n<i>F\u00fcr Einzelkommunikation bitte <strong>ausschlie\u00dflich Email<\/strong> verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.\r<br>\nFor single user communication please send a <strong>email only<\/strong>! PM, Messenger, Chat etc. won't be read.<\/i>","note":"machine-translated from German"}