{"ok":true,"content":"Yes - and with that you&#39;ve introduced an additional, unnecessary level of complexity (external transmitters) that we &quot;removed&quot; with the introduction of VBC 9 years ago because it was always difficult to abstract... sorry for being so blunt, but that&#39;s unfortunately a fact.<br><br> You must do this:<br> <a href=\"https:\/\/www.vstabi.info\/de\/neo_transmitter\" target=\"_blank\" rel=\"noopener noreferrer\">https:\/\/www.vstabi.info\/de\/neo_transmitter<\/a><br><br> And the aids in the PC software &quot;Inhaling&quot;.<br><br><br> Bank switching: Assign a very simple 3-position switch to a channel in your transmitter - and then assign this to this function in your PC.<br><br> Rescue: Assign a channel to a 3-position switch... like this - from the center position, one side is rescue mode and the other is hover mode (if active; hover mode doesn&#39;t make sense with a third-party transmitter because the axis offset can&#39;t be set in flight, but it must be). So, only rescue mode. This MUST ALWAYS be triggered from the &quot;center&quot; position! - If you then use a simple push button for this - configure it accordingly in your system.<br><br> AR is the motor switch, which is supposed to be a 3-way switch. Off - AR - ON - AR becomes active when toggling from On to AR. It doesn&#39;t activate from Off, which wouldn&#39;t make much sense.<br><br> If you intend to control the controller via the AUX\/external transmitter (because we&#39;ve always done it this way) solution, the above MUST also be running for correct AR settings in the FBL. This is because the control parameters are changed in the background when AR and motor shutdown are detected.<br><br> Don&#39;t forget to teach the controller anarchically with a joyride of stick tweaking - this includes the direct output mode in the controller tab.<br><br> RPM switching (when ESC is pressed) occurs via bank \u2013 so switch banks and set it on the PC. If Kontronik is used, then it&#39;s %-e; if others have VGov mode, then it&#39;s the actual RPM.<br><br><br> If the ESC was running here previously - which mode? VGov or ESC Gov? Are RPM or anarchic percentages being specified?<br><br> In any case, the above switchover (if it hasn&#39;t already been messed up) must work as it is (at ESC) - you just need to enter our switches etc. correctly.<br><br><br><br> <strong>I&#39;d look into a VBC (Virtual Base Controller). That way you get rid of all that unnecessary stuff. Plus, the ESC (YGE, Scorpion, Kontronik, Hobbywing) is usually auto-detect, there&#39;s an app for it, no programming required, etc. And I won&#39;t even mention the much simpler setup of the helicopter without a PC, and the battery management for the flight batteries (capacity monitoring of each individual battery including age-related wear)...<\/strong><br>\n<br>\nregards (EN) \/ Gruss (DE) \r<br>\n\r<br>\nRainer Vetter\r<br>\n\r<br>\n_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ \r<br>\nPosting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.\r<br>\n\r<br>\nF\u00fcr Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollst\u00e4ndig abarbeiten. Nehmt Euch Zeit, beantwortet R\u00fcckfragen in Ruhe und vollst\u00e4ndig.\r<br>\n_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ \r<br>\n<i>F\u00fcr Einzelkommunikation bitte <strong>ausschlie\u00dflich Email<\/strong> verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.\r<br>\nFor single user communication please send a <strong>email only<\/strong>! PM, Messenger, Chat etc. won't be read.<\/i><br>\n<br>\n<br>\n<br>\n2 mal bearbeitet. Zuletzt am 11.04.2023 07:50 von RV.","note":"machine-translated from German"}