{"ok":true,"content":"Hello colleagues,<br><br> Last night I had a very frustrating crash with a brand new T-Rex450 Dominator 3S with a built-in NEO ESC (after two trouble-free trim flights). So far, I&#39;ve only found a few clues as to the cause of the crash. Therefore, I would be extremely grateful for any help in finding the cause, especially since I don&#39;t yet have years of helicopter experience. Now, let&#39;s take it step by step:<br><br> I started with a full battery and perfect weather, only hovering at about 2-3 meters altitude (no circuits, no 3D, nothing). I wanted to optimize the trim; yesterday was beautifully calm. I also wanted to see if the Neo message &quot;increased vibration level&quot; is constantly displayed even during hovering.<br><br> I cycled through banks 1-3 smoothly, everything seemed fine. Then, after about 3.5 minutes of hovering in bank three, the helicopter started making unusual noises. It sounded like a vibration, occurring briefly several times before disappearing again. I immediately wanted to switch back to bank 1 and land, but the helicopter had already started to sag slightly. Instinctively, I switched to bank 2 because of the sagging. It immediately sagged again, briefly touched the ground, and then climbed back up to a height of about 2 meters. It then turned right, then dipped downwards, and crashed (the crash site wasn&#39;t visible at the time of the crash, but the tail must have hit the ground). The tail remained relatively stable and isn&#39;t flailing wildly. I must have fiddled with the motor switch, but the motor must have been off at impact, as the entire drivetrain appeared undamaged. However, the entire tail assembly, all servos, and the elevator shaft are destroyed. The rotor head, blade holders, and blades all appear to be without major defects.<br><br> In retrospect, I&#39;m not entirely sure about the exact sequence during the last 1-2 seconds, as everything happened very quickly (as always). A slight confusion in the sequence is possible.<br><br> I would be extremely grateful if you could help me troubleshoot this issue. I&#39;ve attached the Neo log below in text format; the Neo setup file cannot be uploaded due to the &quot;gif, jpg, png, etc.&quot; restriction.<br><br> Here is my preliminary analysis:<br> Apparently, the pitch control of the blades was no longer functioning correctly (error pattern), but no change in rotational speed was noticeable. Using a process of elimination, I proceeded as follows along the chain from the transmitter to the blade control unit to at least get closer to the cause:<br><br> - Graupner MX20 transmitter: no malfunctions so far, no failures, no indications of dropouts. Also extremely reliable in other models so far. OK<br><br> - Power supply model: no indication of failures, Neo-Log is complete. Batteries still 45% full after crash, no indication of defective cells in the battery so far.<br><br> - Receiver GR-16: previously installed in other models, no failures or dropouts so far - everything is great. Neo would have logged this as well. OK<br><br> - NEO: Neo detected vibrations, and shortly before the crash, even a &quot;Dangerous Vibration.&quot; Whether these led to a malfunction of the servos is unclear. General malfunction of Neo \u2013 also unclear. OPEN<br><br> - Servos: Since the helicopter drifted to the right, servo damage to the right roll servo is conceivable (Align DS416 combo servos were installed). Also noteworthy is the indication that the helicopter no longer responded correctly to collective pitch and drifted downwards and to the right. OPEN<br><br> - Mechanics from the servos to the swashplate to the blade grips: everything is rock solid and intact after the crash. Nothing loose or wobbly. Everything&#39;s perfect. OK<br> - Rotor head and blade holders: very smooth-running after removal, no defects visible, everything as it should be upon initial inspection. OK<br><br> Final remarks:<br> - Drivetrain: Before and during the crash, the drivetrain functioned perfectly, with no change in speed, etc. Subsequent inspection of the gearbox was satisfactory (no excessive play, no tooth decay, no wear, backlash OK). The motor ran perfectly after the crash. Bearing clearances were also all OK.<br> - BEC: no undervoltage indicator in NEO. OK<br> - What I absolutely cannot explain is the Neo-Log at 4:35 &quot;Nick sensor is outside the measuring range&quot; even though no ground contact or anything else occurred at that time.<br><br><br> Here&#39;s the Neo log:<br> OK 0:00 Reset Reason: Power On<br> Info 0:05 Calibration complete<br> OK 0:15 Everything is OK (10 sec)<br> OK 0:25 Everything is OK (10 sec)<br> OK 0:35 Everything is OK (10 sec)<br> OK 0:45 Everything is OK (10 sec)<br> OK 0:55 Everything is OK (10 sec)<br> Info 0:58 Speed controller on pitch<br> Info 0:58 Engine switch was set to idle restart<br> Info 0:58 Motor switch was set to ON<br> Warning 1:04 Strong vibration<br> Warning 1:13 Strong vibration<br> Info 1:22 Increased vibration level<br> Info 1:31 Increased vibration level<br> Info 1:41 Increased vibration level<br> Info 1:50 Bank 2 loaded<br> Info 1:50 Increased vibration level<br> Info 1:59 Increased vibration level<br> Info 2:08 Increased vibration level<br> Info 2:17 Increased vibration level<br> Info 2:26 Increased vibration level<br> Info 2:36 Increased vibration level<br> Info 2:45 Increased vibration level<br> Info 2:54 Increased vibration level<br> Info 3:03 Increased vibration level<br> Info 3:12 Increased vibration level<br> Info 3:22 Increased vibration level<br> Info 3:31 Increased vibration level<br> Info 3:36 Bank 3 loaded<br> Info 3:40 Increased vibration level<br> Info 3:49 Increased vibration level<br> Info 3:58 Increased vibration level<br> Info 4:07 Increased vibration level<br> Info 4:17 Increased vibration level<br> Info 4:26 Increased vibration level<br> Critical 4:35 Dangerous vibrations<br> Critical 4:35 Nick Sensor is out of measurement range<br> Info 4:36 Bank 1 loaded<br> Info 4:36 Bank 2 loaded<br> Critical 4:36 Roll Sensor is outside the measuring range<br> Critical 4:36 Nick Sensor is out of measurement range<br> Info 4:36 Speed controller OFF<br> Info 4:36 Speed controller on pitch<br> Info 4:36 Motor switch was set to OFF<br> Info 4:36 Engine switch was set to idle restart<br> Info 4:36 Motor switch was set to ON<br> Critical 4:37 Roll Sensor is outside the measuring range<br> Critical 4:37 Nick Sensor is out of measurement range<br> Info 4:40 Speed controller OFF<br> Info 4:40 No signal from the speed sensor<br> Info 4:40 Motor switch was set to OFF<br> Critical 4:44 Dangerous vibrations<br><br> CONCLUSION: In my view, there are three starting points:<br> 1) Right roll servo defective<br> 2) Due to excessive vibration in the drivetrain, NEO was no longer able to function correctly and controlled the servos uncontrollably.<br> 3) Neo malfunction (however, I consider this rather unlikely).<br><br> That concludes my humble analysis. As I said: I am extremely grateful for any help in finding the cause.<br><br> Greeting,<br> Udo","note":"machine-translated from German"}